|
|
|
|
BILGE PUMPS & ACCESSORIES
Categories
700//750 GPH PUMP (1)
These pumps offer increased capacity in keeping with its 3/4" discharge outlet. 12 volt DC.
PUMPGARD IN-LINE STRAINER (1)
Keeps debris from clogging pump. Runs clearer, longer with less repairs. Clear plastic housing for quick inspection. One screw disassembly and easy cleaning of 1/16" mesh stainless steel screen. Recommended for use with “pressure Max” water pressure system. No mounting is required, just cut intake line and insert. 3/4" slip-on hose connections. Uses replacement screen 361390000.
RULE-A-MATIC® FLOAT SWITCH (2)
Mercury free. Environmentally responsible. Completely sealed metal capsules enhance flawless operation. For use with pumps drawing up to 14 amps.
RULE-A-MATIC® PLUS™ FLOAT SWITCH (1)
Has a strong, impact resistant cover which protects against debris and jamming. Highly abrasion resistant wires exit out the top to keep them out of the water and keeps wear and tear to a minimum. For use with 12, 24, and 32 VDC bilge pumps up to 20 amps maximum.
SHOWER DRAIN PUMP (2)
12V transfer pump for shower and grey water. Runs dry without harm. Operated with a manual on-off switch or an automatic level control. (Switch or level control not provided.) Includes two 1/2" barb port fittings. Install Flojet strainer between shower pan and pump inlet. 4A @ 10 psi. 3.3 gpm.20409043 Service Kit: Check valve assembly (EPDM) diaphragm & pistons (Santoprene). Ball bearing drive & cam (3) Port clips, seal & screws.
Products
2000 GPH PUMP
29-10
Are ignition protected. Double insulated long stack motor. Double strainer non-clogging protection. Compact, efficient and maintenance free. Totally submersible. Runs 100° cooler. No burn-out when More...
500 GPH PUMP
29-25D
Ideal for general purpose use. Can be converted to side or transom mounted pump with model #66 adapter. Can also be used as livewell/baitwell recirculating pump. Features low amp draw, miniaturized to More...
700//750 GPH PUMP
29-20RC
These pumps offer increased capacity in keeping with its 3/4" discharge outlet. 12 volt DC.
AUTOMATIC FLOAT SWITCH
23-42027
Converts bilge pump to automatic operation. Permanently attaches to matching bracket on V-series pump housing. Dimensions: 4-3/4"L x 3-1/4"W x 3"H.
PRO-LINE BILGE PUMP
189-22502
Feature new efficient motor with greater torque and less amp draw, discharge water circulation for cooling, tough resin compound to resist shock, detergents, fuel and corrosives; heavy duty 16-gauge More...
RULE-MATE BILGE PUMP
29-RM1100
Fully automated, it will only turn on when the water level rises. No cycling and no battery drain. Remains off until the internal float switch rises and then stays on only until the water is More...
SAHARA AUTOMATIC BILGE PUMP
23-45057
Includes a 36" length of 16-gauge tinned copper wire. Wire is caulked to prevent water from wicking through insulation jacket. Permanent-magnet motor, stainless steel shaft, and steel-reinforced seal More...
Both the bilge and aerator pumps are powered by the same technology platform — a dependable, long-lasting motor cartridge. Cartridges are replaceable and interchangeable. Housing made of rugged, glass More...
1100 GPH PUMP
29-27D
Offers many features while keeping cost and size to a minimum. Can be converted to side or transom mounted pump with Model #66 adapter. May be used as a livewell/baitwell recirculating pump.
1500 GPH PUMPS
29-51S
High pumping capacity and reliability at a lower cost. Offers more pumping capacity and more exclusive design features than any comparable competitive pump. 1-1/8" discharge outlet.
3700 GPH BILGE PUMP
29-14A
Compact, efficient and maintenance free. Silent running, vibration free. Ignition protected with no burn-out when run dry. Features positive snap-lock strainer base, exclusive Rule moisture tight More...
4000 GPH BILGE PUMP
29-56D24
Designed for the toughest applications. Designed to produce the highest capacity available for a pump its size. 2" discharge outlet.
800 GPH PUMP
29-20F
Designed for smaller boats. The square model features 36 mounting variations as well as a gas resistant stainer base. Easy installation, nylon impeller, stainless steel shaft and replaceable power More...
BILGE BLOWER
189-54124
Radial flow design. Produces a substantial output at relatively low RPM's. Low noise level make excellent for use in heads & galleys. Massive 3" diameter motor idles at 3100 RPM's assuring long life. More...
BILGE PUMP
50-19291
Rugged white ABS plastic construction. 304 stainless steel fasteners. 12V. 600 and 1000 packed in double blisters. 1500 and 2000 packed in printed box. Not recommended for commercial use. Meets NMMA More...
BILGE PUMP INSTALLATION KIT
50-19441
Installation kit contains: 6' (1.8M) corrugated hose; hose clamps; White thru-hull. Use hose clamp 2 #10 stainless steel. Standard carton contains 6 each.
BILGE PUMP SPARE PARTS
6-300030000
Please call our Sales Department for complete ITT spare parts stock and information.SPARE PARTS that are stock items are listed below for Jabsco bilge pumps.